Archive for Term: Silicone & Gelatin

Products 1 - 10 from 11. Products on page
  • Glatzan L 1000ml
    £81.36

    Glatzan L er et flydende syntetisk materiale til dannelse af ultra-tynde bald caps. I et godt ventileret rum påføres Glatzan tyndt og ensartet med pensel på hovedformen og får lov til at tørre. Efter at overfladen er tørret, skal denne procedure gentages mindst tre gange for at nå den ønskede materialetykkelse. De ydre grænser af hætten skal dog bestå af kun 1 eller 2 lag, for at give en særlig tynd kant for flotte overgange. Efter påføring af det sidste lag skal hætten have lov til at tørre helt igennem (i 6-12 timer). Den kan derefter grundigt pudret og forsigtigt fjernes fra hovedformen. Fjernelsesprocessen skal starte ved nakken og derefter langsomt fortsætte i retning mod panden. bald caps skabt på denne måde bør kun bruges, efter at dampene er fuldstændigt fordampet, og efter der er ingen stærkt mærkbar lugt af opløsningsmiddel.

  • Kryolan Glatzan L 1000 ml
    £54.00

    Glatzan L is a liquid synthetic material for creation of ultra-thin bald caps. In a well-ventilated room, Glatzan is thinly and uniformly applied by brush to a head form and allowed to dry. After the surface has dried, this procedure should be repeated at least three times, in order to reach the required material thickness. The outer borders of the cap, however, should consist of only 1 or 2 layers, to provide an especially thin edge for fine transitions. After application of the last layer, the bald cap should be allowed to thoroughly dry all the way through (for 6-12 hours). It can then be thoroughly powdered and carefully removed from the head form. The removal process should start at the nape of the neck and then proceed slowly in the direction of the forehead. Bald caps created in this way should be used only after the fumes have completely dispersed, and after there is no greatly noticeable smell of solvent. Details: 1000 ml

  • Kryolan Glatzan matt 500 ml
    £33.00

    Glatzan Matt is the matt version of Glatzan L for the last coat, to achieve a matt effect. Glatzan Matt is applied thin and uniformly by brush as the last layer on thoroughly dried Glatzan L. Details: 500 ml

  • Kryolan Silicone MF
    £88.00

    Silicone MF is a 2-component impression material that allows taking especially realistic and accurate impressions. It is intended for direct application on the skin. Silicone MF enables taking outstanding, extremely accurate impressions from faces and from other parts of the body. The hair must be covered before starting to take the impression. Scalp hair must be covered by a bald cap, if necessary body hair must be removed. Cover eyebrows generously with make-up remover. Cover eyelashes with enough plastic film to protect them, or use generous amounts of make-up remover. For taking a facial impression, the first step is to prepare 100 g of the 2-component material by mixing it in a disposable cup. Then use a disposable brush to apply the material, with strokes in an upward direction. Repeat this procedure twice, until the required thickness of the impression is reached. If the consistency of the material is too thin for the required procedure, then thicken Silicone MF by adding Kryosil. The next step is to reinforce the silicone impression with Plaster Bandages. After the Silicone MF has hardened sufficiently, then carefully remove the impression from the model. Silicone MF is a very rugged material and can be used many times to produce plaster positives. Mixing ratio A:B (in g): 9:1 Pot Life (minutes): 6 Curing Time (minutes): 30 Shore Hardness: A24 Appearance: cloudy translucent Ultimate Elongation (%): 365 Details: 900 g + 100 g

  • Kryolan Silicone MF Cast 1 kg
    £88.00

    Silicone MF Cast is a proven, well-tolerated 2-component impression material in a creamy consistency. No dripping and flow affect the optimal impression result. Unlike thickening with fillers, chemical thixotropy hardly changes the mechanical properties of Silicone MF Cast after curing. Mixing ratio A:B (in g): 9:1 Pot Life (minutes): 6 Curing Time (minutes): 30 Shore Hardness: A25 Appearance: cloudy translucent Ultimate Elongation (%): 365 Details: 1 kg

  • Kryolan Silicone MF Cast 500 g
    £50.00

    Silicone MF Cast is a proven, well-tolerated 2-component impression material in a creamy consistency. No dripping and flow affect the optimal impression result. Unlike thickening with fillers, chemical thixotropy hardly changes the mechanical properties of Silicone MF Cast after curing. Mixing ratio A:B (in g): 9:1 Pot Life (minutes): 6 Curing Time (minutes): 30 Shore Hardness: A25 Appearance: cloudy translucent Ultimate Elongation (%): 365 Details: 500 g

  • PLATSIL GEL 10 (1 KG KIT)
    £64.99

    Platsil Gel 10 is a unique, 1:1 mix fast curing platinum/addition cure silicone that can be used for making molds, props and masks. With the addition of a Deadener, you can create silicone gel prosthetics and animatronic skins. Platsil Gel 10 has a 5-6 minute working time and a 30 minute demold time, curing to a Shore A10 hardness. Use Platsil Gel 10 as a mold rubber or to create prosthetic appliances. Use the Smiths Deadener to eliminate the synthetic look and feel of ordinary silicone rubbers. Deadened Platsil Gel 10 can be made to look, feel and move like a variety of living tissue. Unlike silicone fluid, Smith’s Theatrical Prosthetic Deadener does not leach from the cured rubber/appliance so bonding and use are far easier.

  • PLATSIL GEL 10 (2 KG KIT)
    £104.99

    PlatSil® Gel-10 This is the Silicone system used by the worlds top Prosthetic technician, It has been used on recent most of the recent oscar nominated films and has seen success in movies such as The Iron Lady, and Harry potter, lord of the rings, and Benjamin Button, Pans Labrinth, and so on and on. It delivers the flesh like results unlike any other silicone product, it is quick easy to use has a nutreul translucent colour and when mixed with mouldlife skin pigments a skin tone and flesh like movement can be created. Platsil Gel 10 is a relatively inexpensive system that can create the most amazing makeup results. The system: 1A:1B (by weight or volume) platinum-cured silicone systems with 6-minute working and 30-minute demold time. PlatSil Gel10 cures to a Shore A10 hardness, But remember to create prosthetic parts you need to add the Smiths deadener to achieve the gel status. Use PlatSil Gels as mold rubbers, to create prosthetic appliances. We offer an array of accessory products that can be used independently or in conjunction with to increase working time; accelerate cure time; thicken the mix for brushing/layering; thin the mix for easier pouring or for softening; or “deaden” the rubber to soften and eliminate the snappy, synthetic look and feel of ordinary silicone rubbers. FEATURES: • Soft, translucent, silicone rubbers • Add “Deadener” to create ultra-realistic prosthetic appliances • Fast 30-minute demold with 6-minute working time • PlatSil® 71R Retarder slows the cure • PlatSil® 71/73X Accelerator speeds the cure • PlatThix thickens the mix to a brushable paste • Bonds to Poly Plastics

  • PLATSIL GEL 25 (2 KG KIT)
    £109.99

    Mouldlife presents the revolutionary Platsil Gel 25, introduced at IMATS London 2014. Combine with either Deadener LV or Part H Hardener for the most versatile product on the market! Less Inventory, More Control. - Exceptionally low A & B mix viscosity - Add Deadener LV to create 'super gel' for prosthetics - Add Part H Hardener to increase to 40 Shore A - Low Shore silicone for animatronics - High clarity for flat moulds - Same great tear strength as Gel 10 - Rapid prototyping moulding material - General purpose moulding material

  • Platsil Gel 25 Silicone Rubber 1kg kit
    £65.99

    Mouldlife presents the revolutionary Platsil Gel 25, introduced at IMATS London 2014. Combine with either Deadener LV or Part H Hardener for the most versatile product on the market! Less Inventory, More Control. - Exceptionally low A & B mix viscosity - Add Deadener LV to create 'super gel' for prosthetics - Add Part H Hardener to increase to 40 Shore A - Low Shore silicone for animatronics - High clarity for flat moulds - Same great tear strength as Gel 10 - Rapid prototyping moulding material - General purpose moulding material